Terra: Engineering Technology I

SolidWorks Student Guide

Download the SolidWorks Student Guide to complete Lessons 1-4.

SolidWorks Practice Guide

Download the SolidWorks Practice Guide to complete Lessons 7-19.

Day 1: SolidWorks Lesson 1

Download the SolidWorks Lesson 1 file and the Dumbell Model file.

Day 2: SolidWorks Lesson 2

Download the SolidWorks Lesson 2 file.  If you use the Switch Plate model found on the website in place of Assignment 4 you will receive a Zero for the entire assignment.

Day 3: SolidWorks Lesson 3

Download the SolidWorks Lesson 3 file.

Day 4: SolidWorks Lesson 4

Download the SolidWorks Lesson 4 file and the Switch Plate for Assembly file and the Claw Assembly file.

Day 5:SolidWorks Lesson 5

Complete Problem Sheet 1 using SolidWorks.

Day 6: SolidWorks Lesson 6

Complete the SolidWorks Challenge Sheet 1 using SolidWorks. SKIP NUMBER 1!!! Do the other 5.

Day 7: SolidWorks Lesson 7

From the Solidworks Practice Guide complete Tutorial / Volume Center of Mass 3-1 and 3-2. The complete all the models found in this Worksheet in Solidworks.

Day 8: SolidWorks Lesson 8

From the Solidworks Practice Guide Complete Tutorial / Volume Center of Mass 3-3 and 3-4. The complete all the models found in this Worksheet in Solidworks.

Day 9: SolidWorks Lesson 9

From the Solidworks Practice Guide complete Tutorial / Simple Cut 3-1 and Tutorial / Volume Center of Mass 3-5. Then complete all the models found in this Worksheet in Solidworks.

Day 10: SolidWorks Lesson 10

From the Solidworks Practice Guide complete Tutorial / Volume Center of Mass 3-6 and 3-7. Then complete all the models found in this Worksheet in Solidworks.

Day 11: SolidWorks Lesson 11

Complete Tutorial / 3dSketch 3-1 and Tutorial / Volume Center of Mass 3-8. Then complete all the models found in this Worksheet in Solidworks.

Day 12: SolidWorks Lesson 12

From the Solidworks Practice Guide complete Tutorial / Volume Center of Mass 3-9, and Tutorial / Volume Center of Mass 3-10. Then complete all the models found in this Worksheet in Solidworks.

Day 13: SolidWorks Lesson 13

Complete Tutorial / Volume Center of Mass 3-11, 3-12, 3-13 and 3-14. Then complete all the models found in this Worksheet in Solidworks.

Day 14: SolidWorks Lesson 14

From the Solidworks Practice Guide complete Tutorial / Volume Center of Mass 3-15, 3-16, and Tutorial / Basic-Intermediate Part 3-1. Then complete all the models found in this Worksheet in Solidworks.

Day 15: SolidWorks Lesson 15

From the Solidworks Practice Guide complete Tutorial / Basic-Intermediate Part 3-2 and 3-3. Then complete all the models found in this Worksheet in Solidworks. Also complete all the models found in this Worksheet in Solidworks.

Day 16: SolidWorks Lesson 16

From the Solidworks Practice Guide complete Tutorial / Basic-Intermediate Part 3-4 and Questions 1 and 2. Then complete all the models found in this Worksheet in Solidworks.

Day 17: SolidWorks Lesson 17

From the Solidworks Practice Guide complete Questions 3, 4 and 5. Then complete all the models found in this Worksheet in Solidworks.

Day 18: SolidWorks Lesson 18

From the Solidworks Practice Guide complete Questions 6, 7, 8 and 9. Then complete all the models found in this Worksheet in Solidworks.




Day 19: SolidWorks Lesson 19

From the Solidworks Practice Guide complete the 4-view part drawing on page 3-61 with A = 40, B = 110 and C = 56.

From the Solidworks Practice Guide complete the 2-view part drawing on page 3-63 with A = 95, B = 60 and C = 60. 

Day 20: SolidWorks Lesson 20

Complete the Adjuster Arm, the Rod Support and the Shaft Support models in SolidWorks.

Day 21: SolidWorks Lesson 21

From the Solidworks Practice Guide complete the Cast Iron Bracket, the Drum with Mounting Axle and the Rod Support #2 models in SolidWorks.